Splitter Delantero Racing V.1 Mazda 6 Mk1 Mps

Splitter delantero v.1 Mazda 6 Mk1 MPS

TYPE OF BODY: SEDAN

VERSION: Mazda6 Mk1 MPS 2006- 2007

____________________

Product information:

- Product made ofABS

- Difusors are protected by a protective foil

- Has UV protection

- Does not require pintar

(If you choose to paint an item, it is necessary to apply primer before pintar.)

- Has stickers that confirm the quality of the product

The material from which our products are manufactured - ABS was created specifically para use in the automotive industry.

ABS is used in production of factory parachoquess and other body parts of the car and these products are characterized con increased strength and flexibility.

The proof of the quality of the manufactured products is theTÜVcertificate.

It confirms the material from which they are manufactured and theTÜVTAILEGUTACHTEN / ABE para the selected products.

The product that holds the certificate is marked con a red tag above the product code.

ABS production is a complex process. The final stage of the production is the manual processing of products and their finishing. This demonstrates the care and accuracy of our piezas. Moreover, the quality control of the products made just before sending them ensures that the defective products are eliminated to a considerable degree.

By purchasing this product you accept the terms of service.

TEMPLATE "SET CONTAINS"

After the final product treatment, the sticker con theTÜVcertificate number is attached.

Each product has an individually selected mounting kit that is included con the product.

FD

Where necessary, brackets are provided para the Difusor to maintain the fixed position of the extended part of the Difusor. Brackets further enhance the look of the Difusor.

The finished set is protected in foil con our company logo and then packed into a shipping carton.

When installing the Difusor, you may need to use an adhesive. In this case, we recommend using polyurethane based adhesive (self-adhesive).

Assembly of the Difusor para the car should be preceded by proper preparation of the surface of the product and the body of the car body.

TEMPLATE "INSTALLATION"

- Installation should begin con adjusting products to the car

FD

Depending on the model of the car, it may be necessary to remove the engine cover or entire parachoques to assemble the front Difusor.

- Mounting needs to drill 14 to 20 6mm holes in the underside of the front parachoques

(Holes should be distributed evenly throughout the width of the parachoques)

• To mount the brackets, it is necessary to drill two holes in the parachoques or in the grill

RD

- Installation requires 8 to 14 holes con a diameter of 6mm in the underside of the rear parachoques (Holes should be distributed evenly).

SD

- para plastic thresholds, mounting involves boring the car's thresholds, the screws are included in the kit (Screws should be spread evenly over the entire length of the threshold). para metal thresholds, we recommend the use of polyurethane based adhesive (to be purchased on your own).

- Before installing, remove the protective foil from the Difusor

- Installation requires proper preparation of the surface of the product and the body of the car body. When using glue (we recommend using polyurethane based adhesive) or tape (we recommend using 3M acrylic double-sided adhesive tape) as an additional adhesive between the piezas. The gluing surface must be previously matted and degreased con an aggressive solvent. After applying the glue the binding time is 24h - the car should not be used at this time.

Plazo de entrega 3 - 4 semanas.

METODOS DE PAGO: Transferencia bancaria, Tarjeta, Paypal y Pago Financiado hasta 12 meses.
GASTOS DE ENVIO: GRATUITOS (solo peninsula)

Marca: MAXTON DESIGN
Referencia: MA-6-1-MPS-CNC-FD1